Unmatched toughness, maximum coverage.
Unmatched toughness, maximum coverage.

Unmatched toughness, maximum coverage.

Land Cruiser wagon with a rooftop tent and the 180 XT MAX Awning open down its side, in a pine forest

180 XT MAX Awning

R 20,615.00
Submit an enquiry
Skip to product information
Land Cruiser wagon with a rooftop tent and the 180 XT MAX Awning open down its side, in a pine forest
1/11

180 XT MAX Awning

R 20,615.00
Taxes included. Shipping calculated at checkout.

Freestanding 180° 4WD Awning · Seamless Canvas · Pole-Free in 30 Seconds


Swing the arms out and you've got 8.53m² of shade across a 5.84m span, running straight down the side of your vehicle and keeping the rear clear. No poles, and no seam above your head: the awning is cut from a single ultra-wide panel of 315gsm acrylic-treated polyester ripstop canvas.


Rated to 50km/h freestanding and over 90km/h when poled, guyed and pegged. Three height adjustable heavy-duty stainless steel L brackets included. B-Tech® Alloy frame. 2-year conditional warranty.


Buy once, buy right.

Read more

View store information

180 XT MAX Awning

Key specifications

Coverage8.53m2
Weight26.5Kg
Minimum mounting distance1.8m
Hinge points2
Description

180 XT MAX: freestanding 180° awning with 8.53m² of seamless shade

The 180 XT MAX is our largest 180° awning: 8.53m² of shade across a 5.84m span, running straight down the side of your 4x4, bakkie or wagon. There are no poles and no seam overhead, and one person can set it up in under 30 seconds: unzip the bag, swing the arms out, then secure the tension straps on the outer arms to the vehicle to tension the canvas.

That's room for a full camp kitchen with prep space, six or more people out of the sun, swags laid end to end, or enough cover to work on the vehicle in the rain.

Why choose a 180° awning

A 180° awning keeps the back of the vehicle completely clear. There's no wrap-around arc crowding barn doors, a lift-up or drop-down tailgate, or a canopy door, so a slide-out kitchen or drop-down table at the rear stays fully usable. If you'd rather have shade wrapped round the rear as well, see our 270° awnings.

Setting up a base camp? Run two 180 XT MAX awnings, one either side of a trailer or canopy, and the whole site is covered.

One panel. No seam over your head.

Most awnings are stitched together from several canvas panels, and every stitch line is a place water can find its way through. The 180 XT MAX awning is cut from a single ultra-wide panel of 315gsm acrylic-treated polyester ripstop canvas, made on a wide loom, so there is no seam above you at all. The only stitching is where the canvas meets the frame sleeves: wet the awning down before its first trip so the core-spun thread swells and seals those stitch holes.

The canvas is tested to a waterhead of more than 1000mm (ISO 811:1981) and treated against UV, mould and mildew, for summer thunderstorms and long seasons of African sun.

Truly freestanding, rated to 50km/h

Two fully trussed arms sit at 90° to the vehicle at each end, fully gusseted for maximum strength. The front and rear arms fold out parallel to the vehicle and are reinforced aluminium with a honeycomb cross-section along their full length, for torsional strength without extra weight.

The result is open, pole-free space underneath. There's nothing to trip over in the dark, nothing to re-peg when you move the chairs, and no trouble setting up on rock shelf, sand or hard-packed gravel where pegs won't bite. It's rated to 50km/h freestanding and to over 90km/h when poled, guyed and pegged down securely. Guy ropes and pegs are included.

Stainless steel headstocks: where the strength starts

The front and rear sections pivot on stainless steel heavy-duty headstocks that retain the stainless steel hinge pin shafts for the arms. The headstocks carry the full load of the open awning into the vehicle mounts, so this is where an awning's strength is won or lost. Stainless steel resists corrosion from salt spray, keeps the arms swinging freely through dust and corrugations, and holds its shape under load.

The rest of the hardware is built to match: B-Tech® Alloy powder-coated aluminium extrusions, double-stitched seams and reinforced stress points at every attachment. Where the ends of the arms attach to the canvas, the canvas is triple-reinforced for additional strength, because that is where most awnings fail. It's also why the 180 XT MAX doesn't need Velcro loops stitched into the canvas along the length of the arms: weaker awnings, with inferior construction and canvas, rely on them to stop the canvas tearing itself apart. It's made for salt spray on coastal runs, fine desert dust and long days on corrugations.

The heavy-duty PVC awning bag is UV and heat stabilised and generously sized, so the canvas goes back in easily even when it's wet or dusty.

Fitting it to your vehicle

The 180 XT MAX comes with three height adjustable heavy-duty stainless steel L brackets. An L bracket must be mounted to the stainless steel headstock at each end of the awning, so you need at least 1.8m between those two mounting points on your rack, canopy or load bars. The third bracket is only needed when mounting to load bars or a roof rack, not a rooftop tent, and normally goes towards the centre of the awning. Packed, it's 2300mm long × 230mm high, and the frame is 170mm wide.

It weighs 26.5kg. As with any roof-mounted gear, add up the awning, brackets, rack and anything else you carry up top, and confirm the total sits within your vehicle's dynamic roof load rating.

Running a Bush Company rooftop tent? The optional Awning-to-Tent brackets mount the awning straight to an AX27, LX27 Gen 2, TX27 or TX27 MAX rooftop tent for a low, tidy roofline.

Add walls when you need them

A 50mm strip of genuine Velcro® brand loop runs the entire length of the valance around the outside edge of the awning. It's rated to hold 3kg per 50mm length, so it's ideal for securing awning walls. Using Velcro rather than a zip along the awning also means there's no zip to rub against the canvas when the awning is packed tightly away in transit. Add the 180 XT MAX Wall Kit for a fully enclosed room with somewhere dry to cook when the weather closes in, or start with one canvas wall or mesh wall as a windbreak or privacy screen. The single walls have full-length YKK spiral zips on both sides, so you can zip canvas and mesh walls together to increase coverage as required.

Usage guidance

  • In windy conditions, use the supplied guy ropes and pegs on the non-trussed arms to prevent upward movement.
  • In heavy rain, run guy ropes off 1-tonne webbing straps between the arms to shed water and reduce the risk of pooling.
  • Lubricate the hinge pins in the headstocks regularly to keep the arms moving freely, especially if you use the awning often in salty coastal conditions.
  • Don't leave it up in snow: the weight stretches the canvas.
  • Wet the canvas down thoroughly before first use.
Specifications
  • Coverage: 8.53m² over a 5.84m span, 180°
  • Canvas: 315gsm acrylic-treated polyester ripstop canvas, single panel, no overhead seam
  • Canvas treatment: UV stabilised, mould and mildew resistant
  • Waterhead: >1000mm (tested to ISO 811:1981)
  • Wind rating: 50km/h freestanding; over 90km/h when poled/guyed and pegged down securely
  • Frame: B-Tech® Alloy extruded aluminium, powder coated; fully gusseted 90° arms, honeycomb cross-section front and rear arms
  • Headstocks: stainless steel heavy-duty, front and rear, retaining stainless steel hinge pin shafts for the arms
  • Awning bag: heavy-duty PVC, UV and heat stabilised
  • Weight: 26.5kg
  • Packed dimensions: 2300mm L × 230mm H; frame 170mm wide (packed width depends on how the canvas is packed)
  • Setup: under 30 seconds, one person
  • Wall attachment: 50mm genuine Velcro® brand loop strip along the entire valance, rated to hold 3kg per 50mm length
  • Included: guy ropes and pegs
  • Warranty: 2 years conditional

Vehicle Compatibility

Needs at least 1.8m between mounting points on your rack, canopy or load bars.

Supplied with 3 height adjustable heavy-duty stainless steel L brackets. An L bracket must be mounted to the stainless steel headstock at each end of the awning. The third is only needed when mounting to load bars or a roof rack (not a rooftop tent) and normally goes towards the centre of the awning.

Installation

Installing Your Bush Company Awning

A copy of the fitting instructions for The Bush Company awnings is available for download here.

The Bush Company or one of our dealers can assemble and install your awning, but if you choose to install the awning yourself please make sure that you have done the due diligence on your intended installation to ensure that it does not create any safety issues and ensure that you follow standard safety precautions when undertaking the install.

Care & Maintenance

Using & Caring For Your Awning

Before Use:

We recommend that new awnings are thoroughly wet down before first use. This lets the core-spun stitching thread swell and seal the stitch holes, so your awning performs well in wet weather.

Deploying & Packing Away:

  • When unzipping the awning, make sure the zippers are right to the top of the bag at each end and that the bottom corners of the bag are not caught on the awning frame.
  • When deploying your awning if the canvas seems excessively tight, STOP and check that the canvas is not caught at the headstock and that it has not slid too far one way in the sail-track on the awning frame.
  • When packing the awning away, ensure that the canvas is not pinched between the awning arms, especially close to the headstock.

Cleaning Canvas & PVC Bag:

  • To clean canvas use a soft brush and cold water.
  • Do not expose to petrol, oils or harsh chemicals.
  • The PVC bag can be cleaned with standard car wash cleaning solution.

Cleaning mould:

Your awning canvas is pre-treated with mould and mildew resistance, but if mould/mildew does occur please follow these steps:

  • Allow mould to dry.
  • Remove surface mould with stiff bristle brush.
  • Vacuum the area.
  • Treat area with Oil of Clove spray (diluted spray can be purchased or can be mixed using a few drops of oil into a spray bottle of water).

Regular Maintenance & Checks:

Like any accessory used in extreme conditions regular maintenance is required to ensure the longevity of your awning, including:

  • Inspect the stainless steel headstocks to identify any bolts that may need re-tightening.
  • Lubricate the hinge pins in the headstocks regularly to keep the arms moving freely, especially if you use the awning often in salty coastal conditions.
  • Ensure that the awning canvas is correctly located in the sail-track on the backing frame to eliminate excessive tension on the canvas.
  • Inspect the attachment of the canvas to the ends of the awning arms.
  • Inspect canvas to identify any wear marks caused by incorrect packing of the canvas.
Delivery

Dispatched every Wednesday

Orders are packed at our Rosslyn warehouse and collected by our couriers every Wednesday. Orders placed by Monday 12:00 go out that Wednesday; later orders go out the following Wednesday.

Delivered to your door

Rooftop tents, awnings and other bulky items travel door to door with our freight partner. Accessories and smaller items go with our courier partners, by Economy or Express, or to a Pargo point or Bob Box locker where available. The exact cost is shown at checkout.

Usual delivery times after dispatch

  • Tents, awnings and freight: 1 to 3 business days in Gauteng, 2 to 5 to other main centres, 4 to 7 to regional areas
  • Smaller items, Economy: 2 to 5 business days
  • Smaller items, Express: 1 to 3 business days

Insured in transit

Every delivery is insured while it's with our couriers, at no extra charge to you. Please check your order on arrival and tell us about any damage within 48 hours.

Or collect for free

Collect from our Rosslyn warehouse on a Wednesday, 8am to 5pm. Choose "Pickup" at checkout.

Namibia, Botswana, Zimbabwe, Lesotho

Order online and choose "Pickup" at checkout, then select our Rosslyn warehouse (if it isn't listed, search for postal code 0200). Your own courier or clearing agent collects on a Wednesday. Prices include 15% South African VAT.

Read our full shipping policy

Stacked with features

Set up in 30 seconds

Set up in 30 seconds

Set up in under 30 seconds. Our stainless steel heavy-duty headstocks retain the stainless steel hinge pin shafts for the arms, so they swing out smoothly and you can kick back faster.

180° freestanding coverage

180° freestanding coverage

No poles means all the shade can be used in the best possible way. 8.53m² of shade coverage offers protection on even the hottest and brightest of days.

No seams, no leaks

No seams, no leaks

Seams are the most common leakage point on awnings. Our unique ultra-wide canvas ream means we can make our 180 XT MAX freestanding awnings with no seams.

Built tough

Built tough

Engineered for the extreme: our B-Tech® Alloy frame and extrusions, fully gusseted main arms and stainless steel heavy-duty headstocks are built tough, providing ultimate strength and durability. Invest once, and own an awning built to last.

Withstand wild weather

Withstand wild weather

Built to take on extreme conditions, our awning stands tall on its own, even when the weather turns wild. For those extra windy days, we’ll keep you grounded with the included guy ropes and pegs. Trust us: your car’s more likely to lift off than this beast.

Next level accessories

Next level accessories

Create your own space with privacy and protection from the elements thanks to the freestanding awning wall kit accessories. Detachable walls are easy to use and turn your outdoor space into a cosy living room with a stunning view.

180 XT MAX Awning features
180 XT MAX Awning features

Not sure which one is right for you?

Compare Our Freestanding Awnings

180 XT MAX Awning 180 XT MAX Awning View details 270 XT Awning Mk2 270 XT Awning Mk2 View details 270 XT MAX Awning Mk2 270 XT MAX Awning Mk2 View details
PriceR 20,615.00R 25,660.00R 31,265.00
FitmentLeft- or right-hand sideLeft- or right-hand sideLeft- or right-hand side
Weight26.5kg27.8kg33.5kg
Awning coverage8.53m²8m²12.2m²
Minimum mounting distance1.8m1.1m1.8m
Pivot points212

FAQs

How much shade does the 180 XT MAX give?

8.53m² across a 5.84m span, running straight down the side of your vehicle and keeping the rear clear for barn doors, tailgates and slide-out kitchens.

What makes the 180 XT MAX worth the investment?

A seamless single panel of 315gsm acrylic-treated polyester ripstop canvas, stainless steel heavy-duty headstocks that retain the stainless steel hinge pin shafts for the arms, fully gusseted B-Tech® Alloy arms and a full modular wall system. It is built as a long-term investment for touring.

What is the canvas made from?

315gsm acrylic-treated polyester ripstop canvas, cut as a single ultra-wide panel so there is no seam overhead. It is treated against UV, mould and mildew.

Is the 180 XT MAX genuinely freestanding?

Yes. Once mounted, no poles or ground supports are needed: the trussed arms carry their own load across the full 5.84m span. It's rated to 50km/h freestanding and over 90km/h when poled, guyed and pegged down securely. Guy ropes and pegs are included; in windy conditions, use them on the non-trussed arms to prevent upward movement.

How long does the 180 XT MAX take to set up?

Under 30 seconds, one person. Unzip the bag, swing the arms out, then secure the tension straps on the outer arms to the vehicle to tension the canvas.

How much does the 180 XT MAX Awning weigh?

26.5kg. The heavier canvas and stronger frame are a deliberate choice for long-term touring. As with any roof-mounted gear, check the total against your vehicle's dynamic roof load rating.

Is the canvas waterproof?

The canvas is tested to a waterhead of more than 1000mm (ISO 811:1981) and is seamless overhead, so there is no stitch line above you to leak. Wet the awning down before first use so the core-spun thread swells and seals the stitching at the frame.

What roof racks is the 180 XT MAX compatible with?

Most roof racks, platform racks and load bars, provided there is at least 1.8m between the two headstock brackets. An L bracket must be mounted to the stainless steel headstock at each end of the awning; the third bracket is only needed on load bars or a roof rack (not a rooftop tent) and normally goes towards the centre. Some rack systems need additional mounting hardware. Always check your rack's dynamic load rating.

Can I install it myself?

Yes. Fitting instructions and install videos are on our Guides & Instructions page. You'll want a second person for the 26.5kg lift. Our dealers can also fit it for you.

Can I add walls to the 180 XT MAX?

Yes. A 50mm strip of genuine Velcro® brand loop runs the entire length of the valance around the outside edge of the awning, rated to hold 3kg per 50mm. It takes the 180 XT MAX Wall Kit and the universal canvas wall for a fully enclosed room.

Will it work with a rooftop tent?

Yes. It mounts alongside AX27, LX27 Gen 2, TX27 and TX27 MAX rooftop tents using the optional awning to tent bracket set.

Should I buy the 180 XT MAX or the 270 XT MAX Awning Mk2?

The 180 gives 8.53m² of straight-line shade down one side at 26.5kg, with a seamless panel and clear rear access. The 270 XT MAX gives 12.2m² wrapping around the rear at 33.5kg. Both need at least 1.8m between the headstock brackets; the 270 XT Awning Mk2 needs only 1.1m.

What warranty comes with the 180 XT MAX Awning?

2 years, conditional, backed by The Bush Company's South African team.

How do I install it? (video)

A copy of the fitting instructions for The Bush Company awnings is available on our Guides & Instructions page.

The Bush Company or one of our dealers can install your awning. If you choose to install it yourself, please make sure you have done your due diligence so that it does not create any safety issues, and follow standard safety precautions while you work.

You may find these videos useful:

Didn’t find your answer?

Don’t hesitate to contact us

Recommended accessories

You may also like